Shipbucket

That black material you normally see on the SQS-53 style domes is more like a steel belted radial tire. Sejong has composite dome. its very sexy.

Must be good for guestimation of the size. There are two types of VLS aft. 32 cells of Mk.41 and 48 cells of K-VLS. The forward 48 cells are also Mk.41.

+ a last round of comments/critics to add to my previous comments


Karl
Now it will be difficult for me to do (help) more in this design


Waiting now a nearly perfect drawing

Sweet ships...well done, guys

The prettiest Burke derative afloat, if you ask me Well done!

_________________
“The person who says it cannot be done should not interrupt the person who is doing it.”

I have updated the Sejong based on the feedback I have recieved.

-the hangar/hull bend is black on your drawing but should be grey, as it is the same angle as the one at the bridge structure
- take an good look at the topmast
- why do the flags spell the burke's callsign? in other words: remove those signal flags, or at least make something useful of it
- aft SPY-1 arrays (or better said, the structure around it) seems to be different from burke flight 2
- bridge wings should not be exact copies of flight 2
- anchor looks wrong
- the RHIB hatch seems to end a bit high....
- I might be wrong, but the lifefrafts on the hangar seem to be not entirely in position. they seem to show at least part of the forward VLS on the hangar, while the aft one is entirely shown.
http://www.c7f.navy.mil/imagery/high-re ... 01-822.jpg
- navigation radar on the mainmast looks different from what you have
http://upload.wikimedia.org/wikipedia/c ... G_991).jpg
- note the differences in colour between the different air intakes. the colour of the intakes seems a bit dark altogether, btw
- you might be able to make that ECM devie on the bridge look a bit better.
- there is an piece of railing missing between the SPY-1 and the mast.
- quite a few edges between structure and hull/deck are rounded, many of yours are diagonals or straight lines.
- there is some sort of block on the hangar which is missing on yours.
- there is something aft of your bridge structure, I think decoy launchers. these are not on your drawing.
- I might be wrong, but are you sure these ships carry SH-60?
and the last note: details, details DETAILS. that is the only thing, apart from the above, to perfect this ship. the back of the hangar is littered with stuff, nothing is visible here. so is the UNREP station just below the RAM. also, the lights on the bridge. said simply, start looking at pictures and find every detail that is worth to spend 2 or more pixels on. IMO, you have no excuse to NOT make these ships perfect, with all the refs and high-res pictures of them.
good luck, but you are almost there!

_________________
Drawings are credited with J.Scholtens
I ask of you to prove me wrong. Not say I am wrong, but prove it, because then I will have learned something new.
Shipbucket Wiki admin

The ship can carry either two Lynx or two SH-60s. What sort of block are you refering to, is it where the antenna sticks up from? The liferafts are out of position because they are from the equipment sheet, and is a little bigger than the ones on the ship irl.

may I ask to draw the SH-60 on the deck and the lynx in the air? then it is clear
the block: look at pics, the side of the hangar. it is completely empty, apart from that one block
the liferafts: I believe they should be a bit more forward and...... nothing stops you from drawing new ones, when the size doesn't fit you are allowed to make new ones (or draw one less, that is the easy solution, the number of liferafts then does not fit but the size is IMO more important then the number.... but the best is IMO to redraw them, or modify their size)

_________________
Drawings are credited with J.Scholtens
I ask of you to prove me wrong. Not say I am wrong, but prove it, because then I will have learned something new.
Shipbucket Wiki admin