Shipbucket

I'm in the throes of revision, so here goes nothing...

You cannot have everything. The WNT disallows the South Dakotas.
And the AU Standards are not exactly the RTL Standards.



Remember this is a WIP. It is intended for advice for improvement.

Wire guidance is not possible before 1950. It has something to do with flexible light weight insulators and wire strength. The whale hull sub with the disappearing deck gun is actually historical for the USN and not only historical but decidedly so, since American design trends before they were sidelined by the German U-cruiser chimera was for the submerged torpedo ambush attack in the RTL with coast defense subs.

Deck gun shown here:



(US Navy recog chart)

Refer to Mister McKinley's Navy for the AU attack on Cadiz to see what this portends.

Suggestion: try using the USN parts sheet if you are drawing USN ships? It'll help you learn and will make your drawings easier to make quickly.

_________________
Best regards,

RegiaMarina1939

The submarines look great, but the turrets on the BBs, CAs, and some of the DDs/Frigates look like they are just a little too rounded out.
also some/some more hull shading would make them look better

just my two cents

_________________
What I like to work on/plan to work on:
US ship Proposals and prototypes
Other ships that haven't yet been put up on Ship bucket
Suggestions Welcomed

Currently working on:
Heavy Cruiser Proposal CA-B: ~80% done.
Heavy Cruiser Proposal CA-C: ~5-10% done.
Heavy/Large Cruiser Proposal CA2-D: ~35% done.
FD Scale P-51A Dazzle Camo Livery: ~5-10% done.
Getting better: Always being worked on.

Finished:
FD Scale P-51D's Dazzle Camo Livery (might be redone)
FD Scale P-51D's German Captured Livery

Hi Tobius: In your BBs the hull hatches are over the belt, making 2 weak points in it. Cheers.

Yes they are. I'm still debating removing the Jacobs Ladders from everything in the next revision. But right now I'm working on a revised parts sheet.

Still a WIP.

the ships look like they would look top heavy to me, i would suggest if you don't want to change the shape, raise the water line a little

_________________
What I like to work on/plan to work on:
US ship Proposals and prototypes
Other ships that haven't yet been put up on Ship bucket
Suggestions Welcomed

Currently working on:
Heavy Cruiser Proposal CA-B: ~80% done.
Heavy Cruiser Proposal CA-C: ~5-10% done.
Heavy/Large Cruiser Proposal CA2-D: ~35% done.
FD Scale P-51A Dazzle Camo Livery: ~5-10% done.
Getting better: Always being worked on.

Finished:
FD Scale P-51D's Dazzle Camo Livery (might be redone)
FD Scale P-51D's German Captured Livery

edited

Look at examples of Japanese and British interwar cruisers and destroyers and at American classes of the same and compare tophamper to the Plimsoll mark.

Especially the Atlantas.

ah ok

_________________
What I like to work on/plan to work on:
US ship Proposals and prototypes
Other ships that haven't yet been put up on Ship bucket
Suggestions Welcomed

Currently working on:
Heavy Cruiser Proposal CA-B: ~80% done.
Heavy Cruiser Proposal CA-C: ~5-10% done.
Heavy/Large Cruiser Proposal CA2-D: ~35% done.
FD Scale P-51A Dazzle Camo Livery: ~5-10% done.
Getting better: Always being worked on.

Finished:
FD Scale P-51D's Dazzle Camo Livery (might be redone)
FD Scale P-51D's German Captured Livery