Shipbucket
http://67.205.157.234/forums/

Russian Pre-Dreadnoughts
http://67.205.157.234/forums/viewtopic.php?f=12&t=11063		 Page 1 of 2
Author:  PhoenixMoscva13 [ June 17th, 2024, 2:45 am ]
Post subject:  Russian Pre-Dreadnoughts
So I noticed one day that the SB wiki lacked some Russian Pre-dreadnoughts so i went ahead and made one (More are planned.)


[ img ]
[ img ]
Author:  olekit24 [ June 17th, 2024, 4:30 pm ]
Post subject:  Re: Russian Pre-Dreadnoughts
it seems your ship is too unproportional - too long or too low. Moreover it has barbette going overboard a little bit. And cannon barrels in casemates must be twice longer.

[ img ]
Author:  PhoenixMoscva13 [ June 17th, 2024, 9:32 pm ]
Post subject:  Re: Russian Pre-Dreadnoughts
I had to improvise a little bit for her guns and right when I finished her, I made a mistake with her length which i had to correct to whatever i could.
Author:  darthpanda [ June 18th, 2024, 10:06 am ]
Post subject:  Re: Russian Pre-Dreadnoughts
PhoenixMoscva13 wrote: *June 17th, 2024, 9:32 pm
I had to improvise a little bit for her guns and right when I finished her, I made a mistake with her length which i had to correct to whatever i could.
It's ok! take you time
Author:  olekit24 [ June 18th, 2024, 5:27 pm ]
Post subject:  Re: Russian Pre-Dreadnoughts
PhoenixMoscva13 wrote: *June 17th, 2024, 9:32 pm
I had to improvise a little bit for her guns and right when I finished her, I made a mistake with her length which i had to correct to whatever i could.
if you know the length of barrel in calibers (and you can guess it, because it is present in the designation of the caliber of the gun barrel), you can just multiply that two parameters anf get the length of barrel in mm. Then simply scale it at your drawing :)
Author:  PhoenixMoscva13 [ June 19th, 2024, 2:04 pm ]
Post subject:  Re: Russian Pre-Dreadnoughts
olekit24 wrote: *June 18th, 2024, 5:27 pm
PhoenixMoscva13 wrote: *June 17th, 2024, 9:32 pm
I had to improvise a little bit for her guns and right when I finished her, I made a mistake with her length which i had to correct to whatever i could.
if you know the length of barrel in calibers (and you can guess it, because it is present in the designation of the caliber of the gun barrel), you can just multiply that two parameters anf get the length of barrel in mm. Then simply scale it at your drawing :)
I've looked for the specific gun but i haven't been able to find any schematics
Author:  darthpanda [ June 19th, 2024, 6:08 pm ]
Post subject:  Re: Russian Pre-Dreadnoughts
[ img ]
[ img ]
[ img ]
Author:  PhoenixMoscva13 [ June 19th, 2024, 9:00 pm ]
Post subject:  Re: Russian Pre-Dreadnoughts
darthpanda wrote: *June 19th, 2024, 6:08 pm
[ img ]
[ img ]
[ img ]
.0.

I NEED THESE!!!!! THANKE!

(Also which vessel is which?)
Author:  heuhen [ June 20th, 2024, 5:16 am ]
Post subject:  Re: Russian Pre-Dreadnoughts
it's written under the drawing, you basically have to mach the Russian names with English names in wikipedia.

I get:
Ekaterina II (Екатерина II)
Chesma (Чесма)
Sinop (Синоп)
Georgii Pobedonosets (Георгий Победоносец)
Author:  PhoenixMoscva13 [ June 21st, 2024, 6:33 am ]
Post subject:  Re: Russian Pre-Dreadnoughts
[ img ]

New Ekaterina-II
Page 1 of 2 All times are UTC
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/